Multi-Function Keyless Entry
MODEL 139.53876
OWNER’S
INSTRUCTIONS
To comply with FCC rules, adjustment or modification of receiver and/or
transmitter is prohibited, except for changing the code setting and replacing the
transmitter battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.
Features
For use with any 53000 SRT series garage door opener
receiver.
Personalized Code: Up to 10,000 possible combinations.
Code can easily be changed if desired.
Operation: Opener activates when 4-code digits and
ENTER button are pressed.
WARNING
Children operating or playing with a garage door opener
can injure themselves or others. The garage door could
close and cause serious injury or death. Do not allow
children to operate the door push button(s) or remote
control(s).
A moving garage door could injure or kill someone under
it. Activate the opener only when you can see the door
clearly, it is free of obstructions, and is properly adjusted.
The keypad will illuminate for 5 seconds at the first push of
any key. If wrong numbers are accidentally pressed,
correction can be made immediately. The ENTER key will
transmit only the last four digits.
The keypad will blink for 15 seconds after the code is
transmitted. During that time you can STOP or REVERSE
door travel just by pressing the ENTER key.
The Lock feature on openers with premium door controls, is
designed to prevent operation of the door from portable
transmitters. However, the door will open and close from
the door control push button and the Multi-Function Keyless
Entry.
Installation
The recommended mounting locations for sectional and one-
piece doors are shown in Figure 3. You can select another
location if you prefer. However, the keypad must be
installed within sight of the door.
Power Supply: 9 Volt battery.
For a one-piece door, use the optional location shown in
the illustration (on the edge of the door jamb) to avoid
injury as the door swings up and out.
Programming the Code
We recommend that you program your personal code
now, before you install the Multi-Function Keyless Entry.
Then you can test the reception at the mounting location
before you proceed further.
Test the reception of the
Keyless Entry by
operating your opener
from the selected
location. Change the
1. Lift the cover to access the keypad, Figure 1. Decide on a
4-digit code using numbers from 0 to 9. You can use a
number more than once (for example, 4, 0, 4, 1).
Exterior Front Wall
1-Piece or
Sectional Door
location if necessary.
Door Jamb Edge
(Optional Location
for 1-Piece Door)
2. Press the selected code digits on the keypad; then press
and HOLD the ENTER button, and press the SRT button
on the opener end panel (behind the Control Center for
screwdrive), Figure 2.
Open the keypad and
remove the battery
compartment screw and
Door Jamb Face
cover to access the
SECTIONAL DOOR ONLY
Figure 1
3. Depending on your opener model, when you
bottom mounting hole
(Figure 4).
KEYPAD MUST BE INSTALLED
WITHIN SIGHT OF THE DOOR
press the SRT button either the opener
light(s) will flash or the garage door
will begin to move. Release the
ENTER button.
Center the keypad at
eye level against the
selected location. Mark 4 1/4" up the
Figure 3
The opener has now learned the
selected code and will respond to future keypad
commands.
centerline from the bottom and drill a
1/8" pilot hole. Install top mounting
screw, allowing 1/8" to protrude
Keypad
Cover
31D431
above surface. Position keypad on
screw head and adjust for snug fit.
To ensure that your portable remote control codes
were not disturbed while you were programming the Keyless
Entry, test your remotes and reprogram them if necessary.
With cover open so bottom mounting
Bottom
mounting hole
hole is visible, use a punch to mark
To change the code in your Keyless Entry at any time,
repeat Steps 1–3.
hole. Remove keypad and drill 1/8"
pilot hole. Replace keypad and
Battery
10A2
complete installation with bottom
Battery
GARAGE DOOR OPENER
(WITH SRT BUTTON)
screw, using care to avoid cracking
plastic housing. Do not overtighten.
Cover
31D430
1
2
3
Green "SRT"
Button
Replace the battery cover.
Battery: The 9 Volt battery should produce
power for at least one year. Replace when
keypad illumination becomes dim.
Figure 4
Green Indicator
Light
Kg
Kg
Figure 2
© 1995 Sears Roebuck & Company
All Rights Reserved
114A1970
Printed in Mexico
|