PYLE Audio Stereo Equalizer PT655E User Guide

 
CONNECTIONS  
EQ  
EQUALIZER  
INTEGRATED CIRCUIT  
AC 220-230V~50Hz  
POWER CONSUMPTION: 10W  
R
E
M
O
T E  
S
YS T E M  
TU  
G
N
D
E
Q
TAP  
E
N
E
R
C
D
RIGHT  
LEFT  
INTEGRATED CIRCUIT  
AC 220V - 230V ~ 50Hz  
TAP  
LAY  
E
E
Q
AV1  
AV2  
P
H
O
N
O
C
D
TU  
N
E
R
P
R
E
C
P
LAY  
R
E
C
L
R
_
_
S
P
E
A
K
E
R
S
6
~
8
A
U
D
I O  
Connection Precautions  
When connecting, either disconnect the power plug from the power outlet or turn off the unit’s power using the  
POWER switch.  
Before connecting, read through the Operation Instructions of the other audio components which will be connected to  
this unit.  
Check the left and right channels and connect properly (L to L and R to R).  
Insert the plugs securely. Improper connection can lead to the generation of noise.  
 
PANEL INFORMATION  
1
2
3
11  
10  
9
8
7
6
5
4
1. ON/STANDBY SWITCH  
Depress button to switch “ON” the unit. Press release to switch “OFF” unit into “STANDBY MODE”. If the unit is left  
unattended for long periods, remove the A/C plug from the power socket.  
2. SPECTRUM DISPLAY  
This displays the sound level different frequency bands (Because the level indicator is connected to the input side, the  
indication does not change when the VOLUME control is turned.  
3. EQUALIZER SETTING  
These settings allow the levels approximate to the frequencies indicated above the controls to be continuously controlled  
from +12 dB to –12 dB for the left and right channels separately.  
Press key () to shift the lower frequency band and key () to shift the higher frequency band that you want to adjust.  
When arrived to the pre-decided band, relative indicator will flash.  
Press level UP () control key or level down control key () to the level that you wish to create, then press MEMORY  
key and select (A-E) to program. And 5 different sets of personally created sound fields can be stored.  
4. EQ MODE SWITCH (FINE/ALT)  
Press the EQ mode switch (4), the word ALT is displayed and the alternating band level can be adjusted. And press it once  
again, the word FINE is displayed & each succeeding sound level can be adjusted.  
5. EQUALIZER FLAT BUTTON  
This button is used to turn the equalizer flat.  
This equalizer also has five pre-memorized 5 different level curves of sound mode including.  
6/7/8/9. CLASSIC/ DISCO / JAZZ / ROCK SWITCH  
If you are listening to the above 4 kinds of music, press the relative modes of switch. The best sound effect will be heard.  
10. DISPLAY/MEMORY MODE SWITCH  
This EQ spectrum has 5 display modes. When pressing DISPLAY/MEMORY switch once, one of the 5 display modes will  
be appeared. And press once again, another one display mode appeared and similarly.  
When you have set the sound level curve of the equalizer personally, pressing the DISPLAY/MEMORY switch, “MEMO”  
will be lit up in the display. And press A-E to memorize it in A-E preset knobs.  
11. USER PRESET SWITCH  
You can press A-E to take your preset sound level curves.  
 
OPERATING PROCEDURES  
EQ  
EQUALIZER  
INTEGRATED CIRCUIT  
AC 220-230V~50Hz  
POWER CONSUMPTION: 10W  
R
E
M
O
T E  
S
YS T E M  
TU  
G
N
D
E
Q
TAP  
E
N
E
R
C
D
RIGHT  
LEFT  
INTEGRATED CIRCUIT  
AC 220V - 230V ~ 50Hz  
TAP  
LAY  
E
E
Q
AV1  
AV2  
P
H
O
N
O
C
D
TU  
N
E
R
P
R
E
C
P
LAY  
R
E
C
L
R
_
_
S
P
E
A
K
E
R
S
6
~
8
A
U
D
I O  
* Switch on the Amplifier or the sound source.  
* Select “EQ” from function selection column at the amplifier or the processor, the relative light will be seen when selected.  
* Switch on the Equalizer by pressing the Power switch (1).  
* Bars of spectrum display in equalizer will be jumping.  
* Press DISPLAY/MEMORY switch, 5 different kinds of display will be shown.  
* When selecting the pre-memorized sound level curves, pressing the SOUND MODE SWITCH (6-9), the relative word  
and sound curve will be seen. A few seconds later, the display will change to spectrum mode automatically.  
* If you want to adjust the your favourite sound level curve, press EQUALIZER SETTING()/ (), the display will  
change from spectrum mode to EQ mode. Choose the frequency firstly, you can adjust the frequency band alternatively  
(by pressing ALT) or each succeeding frequency band (by pressing FINE). Then pressing EQUALIZER SETTING ()/  
() to adjust your favourite sound level. After adjustment, press DISPLAY/MEMORY switch, “MEMO” will be seen on  
the display and press A_E preset. Your 5 favourite sound level curves can be stored in the User Preset Switch.  
* Press User Preset Switch to take your pre-memorized sound level curve.  
 
EQUALIZER CHARACTERISTIC  
Variable range…………………………………±12 dB/ (L & R independently adjustable)  
Center frequencies…………………………….63Hz, 160Hz, 400Hz, 1KHz, 2.5KHz, 6.3 KHz, 16 kHz  
Total harmonic distortion…………………….Less than 0.1% (20 Hz to 20 kHz)  
Maximum output voltage…………………….6V (THD 0.05%)  
S/N ratio……………………………………….60 dB (1HF-A network, 1 V)  
Input impedance……………………………….47 kohms  
Output impedance……………………………..15 kohms  
General  
Power consumption…………………………….10W  
Power requirements  
Power voltage………………………………….220V ~ 50Hz  
For U.K…………………………………………240V ~ 50Hz  
For U.S.A & Canada……………………………110V ~ 60Hz  
Power consumption……………………………. 10 Watts maximum  
Dimensions……………………………………….. 420 mm x 93 mm x 215 mm (W x H x L)  
Weight……………………………………………..2.7 Kg  
Note: We follow a policy of continuous advancements in development, for this reason specifications may be changed  
without notice  
 

Radica Games Games 76073 User Guide
Radio Shack Radar Detector Talking 360 User Guide
RCA Projection Television P46920BL User Guide
RCA Universal Remote D771 User Guide
Reebok Fitness Home Gym RBEX49020 User Guide
Roper Range 9761805 User Guide
Runco Home Theater Screen D 73D User Guide
Samsung DVD Player DVD C600 User Guide
Sanyo Flat Panel Television DP55441 User Guide
Sanyo Network Card POA LN02 User Guide